Connector saver

In the event of a crash, it can happen that your LiPo battery becomes detached from your drone. The force of that happening means the battery mass, at the impact speed, is often focused at the point the connector is attached to the PDB. The result being that the PDB breaks or snaps. The connector saver prevents that from happening. Sitting between the PDB and battery connector, it dampens the force on the PDB, allowing the battery connector to separate, saving the PDB in the process.


PDB soft mount

Hard mounting involves attaching motors or other electronic components directly to your drone frame. For example, the motor rests on top of the frame arm and then screws are attached, from the other side of the arm, to hold the motor in place.

Soft mounting is where some form of cushioned material is placed between, for example, the motor and the frame. Vibrations from the motor are then dampened. Likewise, soft mounting an FC or stack, means any vibrations from the frame are equally dampened.


Some of the benefits of soft mounting are as follows:


  • Your quad flies smoother
  • It allows higher PID tunes, and easier PID tuning
  • Your motors run cooler
  • Video noise is reduced because mechanical vibrations can be translated into electrical noise


FC bobbins

These M3 5x5mm bobbins allow you to separate the different boards that form your stack. In-built cushioning dampens any electrical noise, which makes for a smoother cleaner flight.  


Oomph prop mounts



CL Racing F4sFC v1.4

The F4S is the upgraded version of the original F4 from CL Racing and designed by Cheng Lin. Armattan have worked closely with Cheng on the development of this board and trust it explicity to deliver the best performance with their drones.

It is designed to be simpler to use with many features integrated into the board. This is an all-in-one flight controller for quadcopters with integrated PDB, OSD, buzzer and SD card slot for logging your flights. The layout of this AIO allows for lovely clean builds with ESC solder pads on the top and XT60 pads on the bottom. VTX and cam pads are also on top.



Armattan's Mini Power Distribution Board V3 (Mini PDB V3)

This PDB is used with many frames and comes with the Chameleon frame. As such, it is a general purpose PDB, which Armattan were selling long before the Chameleon was created.


There is a marked place to mount your XT60 connector; hard mounted or by incorporating the connector saver. This PDB is designed for and great with X frames. It also comes with both 5V and 12V linear voltage regulators.

    Armattan Rooster - Accessories

    • Connector saver

      What's included: 1 x XT60 Connector Saver


      PDB soft mount

      What's included: 1 x Armattan PDB soft mount


      NB The PDB shown in the photos is not included. It is shown to aid understanding only.

      FC bobbins

      What's included: 4 x M3 5x5mm bobbins


      Oomph prop mounts

      What's included: 4 x Oomph prop mounts


      CL Racing F4sFC v1.4

      What's included: 1 x CL Racing F4sFC v1.4


      Technical specifications:

      • LiPo Input: 2-6S (5V-30V)
      • Power rail: 3.3v,5v,9v,vbat
      • 132A ( MAX display ) Current sensor with 160A PDB build in
      • 6 layer 2oz Copper PCB
      • Size: 36x36mm
      • Mount Holes: 30.5 x 30.5 mm
      • CPU - STM32F405RGT6 (F4 chip)
      • MPU-6000
      • Full SD Card socket
      • Build in 5V BEC 2A
      • Build-in User selectable 9v or 5v 2A Filtered BEC For camera and VTX
      • Dedicated Camera setting control pads along with camera power signal pads
      • Dedicated VTX connection with along with TX4 for easy connect and control VTX
      • Build in Betaflight OSD
      • 4 UARTS + USB (UART1 , UART3 ,UART4, UART6 ) (Pinout TX1, TX4,RX4, TX6,RX6 )
      • 5V LED strip output
      • 4 motors on each corner for a better layout.
      • Support RX : Dedicated Sbus hardware inverted ,Satellite RX, Ibus,TBS Crossfire
      • Dedicated hardware inverted connect to UART3 for smartport telemetry
      • 4 in 1 esc socket with external current sensor input
      • Support TP and Smartaudio VTX
      • Buzzer pads for external buzzer



      What's included: 1 x Armattan Mini Power Distribution Board V3 (Mini PDB V3)


      Technical specifications:

      • Rated up to 6S at 140 amps
      • 5V voltage regulator12V voltage regulator
      • 5v and 12v regulators are rated up to 1 amp each
      • 30.5mm x 30.5mm mounting holes

      • XT60 solder point

    1st class or Special Delivery  -  fast & free UK shipping  -  on all products


    Prices include VAT

    Created by Light Limited (03846870) VAT GB207237332

    West Yorkshire based, UK company

    Secure online payments